website hit counter

How Many Coats Of Wipe On Poly

In Wood 100 views

So an additional coat may be in order. If minimal i would recommend 3 4 coats of wipe on poly.

Oil Based Vs Water Based Polyurethane Valenti Flooring

Master The Art Of Wipe On Poly Construction Pro Tips

Master The Art Of Wipe On Poly Construction Pro Tips

And im talking minwax poly if theres a better one of those please tell me too.

How many coats of wipe on poly. You need many more coats when applying it thinned but the build is nicer in the end. Also even lightly scuffing it between coats seems to take much of the material off. Hi i have built a small nightstand and have been using minwax wipe on poly to finish.

The minwax wipe on when i use it at above 72 f. Sometimes its one sometimes its 10. Of course with something as absorbent as mdf your first coat will be almost completely absorbed.

Im looking for a really nice satin finish like the ones on the american deluxe teles. I have 2 coats on the legs and aprons and three on the top. Spray poly goes on just like spray paint.

I do wait overnight before. You can thin polyurethane 5050 or even a little more with mineral spirits to make it easy to wipe. Minwaxs wipe on poly is also a good choice though its more expensive to buy pre thinned.

Some woodworkers like to use spray poly for a thin top coat over base coats of conventional polyurethane producing a final smooth coat without brush strokes. After i get about 3 coats on that usually takes all day because i do other things i wait over night for the next coats. Minwax wipe on poly.

If this table will be used much more frequently i would recommend the satin brush on poly in the quart can again with 3 maybe 4 coats. Minwax wipe on poly is basically minwax polyurethane varnish thinned out with mineral spirits to allow it to be wiped on rather than brushed. My normal brushing schedule is to apply the first coat thinned 50.

Is usually dry enough to steel wool and then re coat in 6 hours or less as long as you dont goop on thick coats. Im about to use the wipe on poly and if thats better id like to know d. Now this many coats of satin finish can make the finish look very mirky.

Andy ive used minwax wipe on poly a lot over the years i really like it. Just depends on the look i like. So i like to apply 7 to 10 coats.

Wipe on poly is applied with a clean lint free rag. I only use as many as that project needs. I hope this helps bill.

A single layer of wipe on poly is very thin compared to poly you brush on. I like to use at least 5 or 6 coats because of the wipe on process. For the first few coats i just wait a few hours at minimum.

It really doesnt allow much material to be put on for each coat. If you use a wiping varnish you need to wipe on 2 3 coats to equal one brushed on coat. I use wipe on poly.

My queestion is how many coats is enough.

Super Smooth Poly Finish Popular Woodworking Magazine

My Tips Tricks For Finishing With Minwax S Wipe On Poly High

Varathane 1 Qt Satin Wipe On Water Based Polyurethane 339751 The

Tags: #how many coats of wipe on poly #how many coats of wipe on poly before sanding #how many coats of wipe on poly for dining table #how many coats of wipe on poly for table top #how many coats of wipe on poly guitar #how many coats of wipe on polyurethane

How Many Coats Of Wipe On Poly Guitar
How Many Coats Of Wipe On Poly Guitar
If youre tired of the look of
How Many Coats Of Wipe On Poly For Table Top
How Many Coats Of Wipe On Poly For Table Top
General finishes high performance water based topcoat
How Many Coats Of Wipe On Poly For Dining Table
How Many Coats Of Wipe On Poly For Dining Table
Tung oil dries slowly and needs many
How Many Coats Of Wipe On Polyurethane
How Many Coats Of Wipe On Polyurethane
Dark walnut stain and polyurethane case of
Must read×

Top